Network Cabling in San Francisco CA – #1 C7 Licensed Contractor

Network Cabling in San Francisco CA – Installed, Tested & Certified

We install commercial network cabling in San Francisco CA: Cat6 and Cat6A data cabling, Ethernet drops, patch panels and PoE-ready runs for offices, warehouses, schools and medical facilities, with every link tested and certified before handoff.

Whether you need twelve new drops for a conference room or six hundred for a full-floor buildout, our C-7 licensed technicians pull the cable, terminate it to jacks and panels, label both ends and hand your IT team a certification report for every run.

Adding drops, moving offices or replacing old Cat5e? Get an itemized network cabling quote — call (628) 215-7235.

Request a quote

Network Cabling Services

Every network cabling project starts with installation and ends with certification. Choose the service that matches your project, or call us and we’ll scope the right mix.

Network Cabling Installation

New horizontal cabling, moves, adds and changes, pulled from the telecom room to every workstation, access point and device.

How We Install and Configure Network Infrastructure Cabling

Each run starts in the MDF or IDF, where we mount patch panels and horizontal cable managers in the rack. From there we pull cable through J-hooks, cable tray or conduit, keeping at least 12 inches from fluorescent fixtures and electrical feeders and holding a bend radius of four times the cable diameter.

At the workstation end, we’re installing low-voltage mounting brackets, surface raceway or floor boxes, then terminating each cable to a T568B keystone jack. Back in the rack, every port is punched down, dressed with Velcro, labeled to TIA-606 and connected to the switch with color-coded patch cords.

For PoE devices, we size the cable to the load: Cat6A handles 802.3bt Type 4 power for Wi-Fi 7 access points and PTZ cameras with less heat rise in large bundles, while Cat6 is a cost-effective fit for desk phones and workstations.

48-port Cat6A patch panel terminated to T568B with horizontal cable managers and Velcro-dressed cable bundles
48-port Cat6A patch panel terminated to T568B, with 1U horizontal managers between panels and Velcro-dressed bundles of no more than 24 cables to limit PoE heat rise.

Where We Run Commercial Cabling, From Offices to Data Center Rooms

  • Open-plan offices and workstations
  • Conference and huddle rooms
  • Wireless access point locations
  • IP camera and access control points
  • Warehouse and distribution floors
  • Classrooms and school IDFs
  • Medical exam rooms and nurse stations
  • Retail POS and back-office areas
  • Server rooms, data center racks and telecom closets

Recent network cabling work by neighborhood

Jackson Square historic offices

Fishing Cat6 through the brick walls and timber ceilings of 1850s-era buildings for architecture and law firms, using surface raceway where the landmark rules limit open walls.

Dogpatch light industrial

Cat6A runs to rugged enclosures for makers and fabrication shops along 3rd Street, with cable in conduit to protect it from forklifts and machinery.

Yerba Buena hotels near Moscone

Overnight upgrades of guest-floor and ballroom drops for hotels serving convention traffic, scheduled around room blocks and events.

Embarcadero pier offices

Network cabling for offices inside converted waterfront piers, routed along steel trusses where there’s no drop ceiling to hide cable.

Cat5e vs Cat6 vs Cat6A: Network Cable Specifications

The cable you choose decides how fast your network can run and how much PoE it can carry. For most new San Francisco office buildouts, we recommend Cat6A to the access points and Cat6 or Cat6A to the desk.

Network cable category specifications
Category Bandwidth Max speed 10 Gbps distance Best for
Cat5e100 MHz1 Gbps (2.5G with NBASE-T)Not supportedExisting cabling only; not recommended for new installs
Cat6250 MHz10 GbpsUp to 55 mWorkstations, VoIP phones, printers
Cat6A500 MHz10 GbpsFull 100 m channelWi-Fi 6E/7 APs, PoE++ devices, future-proof drops
Cat6A shielded (F/UTP)500 MHz10 GbpsFull 100 m channelHigh-EMI areas: labs, medical imaging, industrial

Network Cabling Testing & Certification

Every copper link is certified against TIA-568.2-D permanent link limits, measuring wire map, length, insertion loss, NEXT and return loss on all four pairs. Failing links are reterminated and retested before we leave, and you get exported PDF reports organized by telecom room and panel. Learn about our testing and certification.

Diagram comparing a Cat6A permanent link test and a channel test for network cable certification
Passing Cat6A permanent link at 87 m with 3.2 dB worst-case NEXT margin, well inside the 90 m permanent link limit set by TIA-568.2-D.

Network Cabling Service Area

We install network cabling in every neighborhood in the city, plus these nearby cities:

See every location on our service area page.

Request a Quote From Our Network Cabling Company

Send a floor plan or drop count, and we’ll schedule a site walk and return an itemized quote, usually within two business days.

San Francisco Telecom Techs
One Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]

Get your network cabling installed, labeled and certified on schedule.

Request a quote

Send us your project details