MDF / IDF Build-Out in San Francisco CA – #1 C7 Licensed Contractor

MDF / IDF Build-Out in San Francisco CA

We build main and intermediate distribution frames from an empty closet: racks and cabinets, overhead ladder rack, grounding and bonding, dedicated power, seismic bracing and fiber patching, finished and labeled so your network infrastructure has a clean, documented home.

Need an MDF / IDF build-out in San Francisco CA? Our C-7 licensed crews turn bare space into a working network closet, coordinate power and HVAC with your other trades, and land every copper and fiber run on a labeled patch panel. Whether you need one wall-mount rack or a full main frame with a dozen racks, the space is ready before your networking gear arrives.

Planning a new network closet or cleaning up an old one? Get a site walk and itemized quote. Call (628) 215-7235.

Request a quote

MDF vs IDF: What Each Space Does

Most networks have one main distribution frame and, in larger spaces, one or more intermediate distribution frames. Getting the role of each right decides where cable runs, how much space you need and how easily the network can grow.

MDF (main distribution frame)

The central hub where carrier circuits arrive from the point of entry, core switches and firewalls live, and the fiber backbone starts. There’s one per building or tenant space, usually with the most racks, power and cooling.

IDF (intermediate distribution frame)

A satellite closet on each floor or zone, tied to the main frame by backbone cabling. It holds access switches and patch panels for the horizontal runs that feed desks, access points and cameras, keeping every run under the 90 m limit.

What We Install in Your MDF and IDF

A build-out covers every layer between an empty closet and a working network. We handle each one, or pick up where your general contractor leaves off.

  • Racks, cabinets and wall mounts

    Two- and four-post open racks, enclosed server cabinets, and swing-out wall-mount racks for small closets, laid out with front and rear clearance for service.

    • 2-Post / 4-Post
    • Server Cabinets
    • Swing-Out Racks
    • Rack Elevations
  • Ladder rack and cable management

    Overhead ladder rack, waterfall drops, and a horizontal cable manager above every patch panel, so cords reach each port without kinks or crossed bundles.

    • Ladder Rack
    • Waterfalls
    • Vertical Managers
    • Horizontal Managers
  • Grounding and bonding

    A telecommunications main grounding busbar (TMGB) in the main frame and a TGB in every satellite closet, tied together with a bonding backbone and bonded to structural steel.

    • TMGB / TGB
    • Bonding Backbone
    • Rack Bonding
    • TIA-607
  • Power and UPS

    Dedicated circuits coordinated with your electrician, rack-mount PDUs and UPS units sized to keep switches and PoE devices running through short outages.

    • Dedicated Circuits
    • Rack PDUs
    • UPS
    • Electrician Coordination
  • Seismic bracing

    Racks anchored to slab and braced overhead, which matters in an earthquake zone and is often required by property engineers.

    • Slab Anchors
    • Top Bracing
    • Seismic Kits
    • Engineer Approval
  • Fiber and copper patching

    Fiber enclosures, patch panels and backbone terminations between the main frame and each satellite closet, labeled so any port can be traced in seconds.

    • LC Fiber Enclosures
    • Patch Panels
    • Backbone Tie-In
    • TIA-606 Labels

Network Closet Requirements & Standards

A well-built distribution frame follows ANSI/TIA-569 for space design and ANSI/TIA-607 for grounding. These are the targets we plan to, adjusted for your property and equipment.

Design requirements for distribution frame build-outs
RequirementTypical targetWhy it mattersReference
Closet sizeAbout 10 × 8 ft for up to 5,000 sq ft served; 10 × 11 ft for up to 10,000 sq ftSpace for racks plus front and rear service clearanceTIA-569
Closets per floorAt least one per floor, within 90 m of every outletKeeps horizontal runs inside the permanent link limitTIA-568 / TIA-569
Clearance36 in in front of and behind racks; 8 ft minimum ceiling heightSafe access for installs, moves and repairsTIA-569
GroundingTMGB in the main frame, TGB in each satellite closet, #6 AWG minimum bonding conductorProtects equipment and people from surges and faultsTIA-607
PowerDedicated circuits for racks, plus UPS sized to switch and PoE loadKeeps phones, APs and cameras up through short outagesNEC / local code
Environment64–75°F and 30–55% relative humidity, with cooling sized to equipment heatPrevents overheating in closets full of PoE switchesTIA-569
SeismicRacks anchored to slab and braced overheadKeeps equipment standing in an earthquakeCBC / property engineer
Finished main distribution frame with network racks, overhead ladder rack and labeled fiber enclosures
A finished main frame with three 45U four-post racks anchored to slab and braced to 12-inch ladder rack, a TMGB bonded to structural steel with #6 AWG conductor, and labeled LC fiber enclosures feeding four satellite closets.

Spaces we build out

  • New main frames
  • Floor IDF closets
  • Small-office network closets
  • Server closets
  • Shared riser closets
  • Converted storage closets
  • Lab and clinical network closets
  • Warehouse network enclosures

Network Closet Build-Outs Across the City

Financial District closet conversions

Turning tight storage closets in older Montgomery Street towers into satellite closets, with compact racks and careful cooling where floor space is scarce.

SoMa ground-up main frames

New core closets in converted warehouse offices, built alongside the general contractor so power, cooling and ladder rack are in before drywall.

Mission Bay lab network closets

Separate closets for lab instruments and corporate IT in life science properties, built to each landlord’s base standard.

Bayview warehouse enclosures

Lockable cabinets placed mid-warehouse so long horizontal runs stay inside the 90 m limit.

How We Build Out an MDF or IDF

  1. Survey and design

    We measure the space, confirm power, cooling and door access, and draw rack elevations showing every patch panel, switch and UPS.

  2. Trade coordination

    We hand power, HVAC and backboard requirements to your electrician and general contractor so the space is ready for us.

  3. Racks, ladder rack and grounding

    Racks are anchored and braced, ladder rack goes overhead, and the grounding busbar is installed and bonded.

  4. Patch panels, keystone jacks and terminations

    Fiber enclosures are mounted, each horizontal run is punched down to a jack at the desk and a patch panel port in the closet, and everything is dressed and labeled.

  5. Testing and handoff

    Every link is certified from jack to panel, and you receive rack elevations, a port map and test reports for the finished closet.

A build-out usually goes hand in hand with these services. See every related service on our main service overview.

MDF / IDF Build-Out Service Area

We build distribution frames in every neighborhood of the city, plus these Peninsula, East Bay and Marin cities:

See every location on our service area page.

Request an MDF / IDF Build-Out Quote

Send closet dimensions, a floor plan or a photo of the space, and we’ll schedule a site walk and return an itemized quote, usually within two business days.

San Francisco Telecom Techs
One Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]

Get a network closet that’s built, labeled and ready for your gear.

Request a quote

Send us your project details