Short answer: When you group telecommunication by the medium that carries the signal, the three types are wired (copper) communication, fiber optic communication and wireless communication. Wired systems send electrical signals through copper cable. Fiber optic systems send pulses of light through thin strands of glass. Wireless systems send radio waves through the air.
You will also see two other “three types” lists: one based on the direction information travels (simplex, half-duplex and full-duplex) and one based on what is being sent (voice, data and video). We cover all three ways of looking at it below.
Telecommunication simply means sending information over a distance using electronic or optical signals. A phone call, an email, a security camera feed and a Zoom meeting all count. What changes from one system to another is how the signal gets from point A to point B, and that is where the three types come from.
If you are new to the topic, our guide on what telecommunication is in easy words is a good starting point. If you manage an office, warehouse or school, this article will also help you understand which type of cabling your building actually needs.
Type 1: Wired (Copper) Telecommunication
Electrical signals over metalWired telecommunication is the oldest of the three types. It sends information as electrical signals through copper conductors. The first telegraph lines in the 1840s and the first telephone networks were both copper, and copper is still the most common cable inside commercial buildings today.
There are two main kinds of copper cable you will run into:
- Twisted pair cable. Four pairs of copper wires twisted together to cancel out interference. This is the Ethernet cable you see plugged into computers, phones and cameras, sold in categories such as Cat5e, Cat6 and Cat6A.
- Coaxial cable. A single copper core surrounded by shielding. It is used for cable TV, cable internet and older analog security cameras.
- Common examples
- Office Ethernet, desk phones and VoIP handsets, IP security cameras, landline telephone service, cable TV.
- Strengths
- Low cost, easy to terminate and repair, and able to carry power along with data through Power over Ethernet (PoE), which runs Wi-Fi access points, cameras and phones without a separate outlet.
- Limits
- An Ethernet channel tops out at 100 meters (about 328 feet), and copper can pick up interference from nearby electrical lines and motors if it is not installed correctly.
In a typical office, copper does the “last stretch” of the work: it runs from the telecom room to each desk, phone, camera and ceiling access point. Getting that stretch right is what network cabling installation is all about.
Type 2: Fiber Optic Telecommunication
Light pulses through glassFiber optic telecommunication sends information as pulses of light through strands of glass about as thin as a human hair. A laser or LED at one end switches on and off billions of times per second, and a receiver at the other end turns that light back into data.
Because light does not carry electrical current, fiber is immune to electrical interference and can carry far more data over far longer distances than copper. That is why the backbone of the internet, the undersea cables between continents and the links between floors of a high-rise are almost always fiber.
- Single-mode fiber (such as OS2) uses a very small core and a laser. It is built for long runs: between buildings, across a campus or across a city.
- Multimode fiber (such as OM4) uses a larger core and is designed for shorter runs inside a building, like connecting the main telecom room to each floor.
- Common examples
- Internet service provider lines, building backbones between MDF and IDF rooms, data centers, campus networks, undersea cables.
- Strengths
- Enormous bandwidth, very long distances (single-mode fiber carries 10 Gbps for 10 km or more), no electrical interference and hard to tap.
- Limits
- Higher material and installation cost, and the glass has to be joined by fusion splicing or precision connectors, which takes specialized tools and training.
Fiber does not usually go to every desk. Instead it acts like a highway between telecom rooms, and copper takes over for the local streets. You can read more about how that is planned on our fiber optic cabling page.
Type 3: Wireless Telecommunication
Radio waves through the airWireless telecommunication sends information through the air using electromagnetic waves, mostly radio and microwave frequencies. No cable connects the sender and the receiver. Instead, both sides use antennas tuned to the same frequency.
Wireless covers a huge range of technologies:
- Wi-Fi for laptops, phones and tablets inside a building, using the 2.4 GHz, 5 GHz and 6 GHz bands.
- Cellular networks (4G LTE and 5G) for mobile phones and data.
- Radio and television broadcasting, one of the oldest forms of wireless communication.
- Microwave links that beam data between rooftops or towers in a straight line.
- Satellite communication for remote areas, GPS and global broadcasting.
- Bluetooth for short-range connections like headsets and keyboards.
- Common examples
- Office and guest Wi-Fi, cell phones, two-way radios, broadcast TV and radio, satellite internet.
- Strengths
- Mobility and convenience. Users can move around freely, and new devices connect without pulling a new cable.
- Limits
- Signals weaken through concrete, steel and glass, nearby networks can interfere with each other, and capacity is shared among everyone connected to the same access point.
Here is the part many people miss: wireless is rarely wireless all the way. Every Wi-Fi access point and every cell tower is connected back to the network by cable. In an office, each access point usually sits on a Cat6 or Cat6A drop that also powers it through PoE. Weak Wi-Fi is often a cabling problem, which is why commercial Wi-Fi installation starts with the wiring behind the ceiling.
The Three Types of Telecommunication Compared
| Wired (copper) | Fiber optic | Wireless | |
|---|---|---|---|
| Signal type | Electrical current | Pulses of light | Radio and microwave signals |
| Typical distance | Up to 100 m per Ethernet channel | Hundreds of meters (multimode) to 10 km+ (single-mode) | Tens of meters (Wi-Fi) to miles (cellular, microwave) |
| Typical speed | 1 Gbps (Cat6), 10 Gbps (Cat6A) | 10 Gbps to 100 Gbps and beyond | Shared; varies with distance, walls and number of users |
| Interference | Can be affected by electrical noise | Immune to electrical interference | Affected by walls, distance and other networks |
| Carries power? | Yes, through PoE | No | No |
| Relative cost | Lowest | Highest per link | Low per user, but needs cabled access points |
| Best for | Desks, phones, cameras, access points | Backbones, building-to-building, ISP lines | Mobile devices and open spaces |
Other Ways to Group the Three Types of Telecommunication
Depending on the textbook or class, “the three types of telecommunication” can mean something different. Here are the two other groupings you are most likely to see, so you can recognize the answer no matter how the question is asked.
By direction: simplex, half-duplex and full-duplex
- Simplex communication goes one way only. Broadcast radio and TV are simplex: the station sends, and your radio or TV only receives.
- Half-duplex communication goes both ways, but only one side can talk at a time. A walkie-talkie is the classic example, which is why people say “over” when they finish speaking.
- Full-duplex communication goes both ways at the same time. A phone call and a modern Ethernet connection are full-duplex, so both sides can send and receive at once.
By content: voice, data and video
- Voice communication carries speech: landlines, cell calls, VoIP phones, intercoms and overhead paging.
- Data communication carries files, email, web traffic and business applications over computer networks.
- Video communication carries moving images: video conferencing, security camera feeds and television.
Today, most voice, data and video travel over the same IP network, which is why a single, well-built cabling system can support phones, computers, cameras and conference rooms all at once. For a broader look at how these categories fit together, see the different types of telecommunications.
How the Three Types Work Together in a Commercial Building
In real life, businesses do not pick just one type. A typical San Francisco office uses all three, each doing the job it does best:
- Fiber brings service in. The internet provider delivers service to the building over fiber, landing in the main distribution frame (MDF).
- Fiber connects the floors. A fiber backbone runs up the building riser from the MDF to an intermediate distribution frame (IDF) on each floor.
- Copper reaches every device. From each IDF, Cat6 or Cat6A cable runs to desks, phones, printers, cameras and ceiling access points, all within the 100 meter limit.
- Wireless covers the people. Access points turn that wired connection into Wi-Fi so laptops and phones can roam the floor.
If any one layer is weak, the whole network suffers. A fast internet line will not help if the copper to the access points is old Cat5e, and great Wi-Fi hardware cannot fix a backbone that was spliced poorly. That is why structured cabling designs all three layers as one system and tests and certifies every link.
Which Type of Telecommunication Does Your Business Need?
The honest answer is usually “all three, in the right places.” A few quick rules of thumb:
- Use copper for anything that stays in one place and needs reliable speed or power: workstations, VoIP phones, IP cameras, card readers and access points.
- Use fiber for long runs, runs between telecom rooms or buildings, and any link that needs 10 Gbps or more over more than 100 meters.
- Use wireless for mobile devices, guests, warehouses with moving scanners, and areas where pulling cable to every user is not practical.
If you are planning a move, a tenant improvement or a network refresh, a site walk is the fastest way to find out what your building already has and what it needs. You can also learn what a telecommunications contractor does before you call one.
Need fiber, copper or Wi-Fi installed in the Bay Area? Call (628) 215-7235 for a site walk.
Request a quoteFrequently Asked Questions
What are the three types of telecommunication?
Grouped by the medium that carries the signal, the three types are wired (copper) communication, fiber optic communication and wireless communication. Copper carries electrical signals, fiber carries light, and wireless carries radio waves through the air.
What are the three types of telecommunication by direction?
Simplex (one way only, like broadcast radio), half-duplex (both ways but one at a time, like a walkie-talkie) and full-duplex (both ways at the same time, like a phone call).
Which type of telecommunication is fastest?
Fiber optic communication offers the most bandwidth over the longest distances. Single-mode fiber carries 10 Gbps for 10 kilometers or more and supports 100 Gbps and higher with the right optics, while copper Ethernet is limited to a 100 meter channel.
Is Wi-Fi wired or wireless telecommunication?
Wi-Fi is wireless between your device and the access point, but every access point connects back to the network with a cable, usually Cat6 or Cat6A that also delivers Power over Ethernet. Good Wi-Fi depends on good cabling behind it.
Does a business need all three types of telecommunication?
Most commercial buildings use all three. Fiber connects the building and its telecom rooms, copper reaches desks, phones, cameras and access points, and wireless covers laptops, phones and other mobile devices.
Keep Reading
Talk to a San Francisco Telecommunications Contractor
Send a floor plan, drop count or a description of the problem, and we’ll schedule a site walk and return an itemized quote, usually within two business days.
San Francisco Telecom TechsOne Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]