Security Camera Cabling in San Francisco CA
We run the lines behind your surveillance: Cat6 PoE runs from the telecom room to every device, outdoor runs in conduit, and fiber for parking lots and yards beyond copper’s reach.
Need security camera cabling in San Francisco CA? Our C-7 licensed technicians plan each mounting location with you, pull and terminate a dedicated run to every device, protect outdoor runs from weather and surges, and certify every link, so your commercial security stays powered, online and recording clear footage day and night.
Adding new devices or replacing old coax? Get an itemized quote. Call (628) 215-7235.
Request a quoteWhy the Run Behind Each Device Matters
An IP dome or bullet depends on one line for everything: footage back to the recorder and PoE power for the unit, its infrared lights and, on outdoor models, its heater. Long runs, damaged jackets, copper-clad wire and unprotected outdoor connections are the usual reasons devices drop offline, reboot at night when the IR turns on in low light, or record grainy footage. Doing the runs right prevents all of these before the first unit goes up, whether you’re replacing old CCTV cabling or adding security cameras to existing security systems.
What’s Included in Every Surveillance System Run
-
PoE drops
A dedicated Cat6 home run from the IDF to every device, carrying footage and PoE power on one line, labeled by device ID.
-
Outdoor and perimeter runs
Outdoor-rated Cat6 in conduit to wall, roof and pole mounts, with weatherproof junction boxes, drip loops and surge protection where runs enter the building.
-
Long runs past 100 meters
Parking lots, yards and gates beyond copper’s reach get fiber with media converters, or PoE extenders for shorter gaps.
-
PTZ and high-power units
Cat6A and 802.3bt-ready runs for PTZ, multi-sensor and heated outdoor units that draw more power than a standard dome.
-
Analog to IP upgrades
Replacing old coax with Cat6 for IP devices, or using Ethernet-over-coax adapters as a stopgap where new runs aren’t possible yet.
-
NVR and head-end work
Patch panels, PoE switches, UPS power and tidy cable management in the telecom room, sized so every device has power and a clean path to the recorder.
Surveillance Cameras and the Runs They Need
Here’s what we plan for each type of unit. Exact power depends on the model, so we confirm it against the manufacturer’s data sheet during design.
| Device type | What we install | Max run | PoE standard | Notes |
|---|---|---|---|---|
| Indoor dome or turret | Cat6, plenum where required | 100 m | 802.3af | Most common in offices and stores |
| Outdoor bullet or dome with IR | Outdoor-rated Cat6 in conduit | 100 m | 802.3af or 802.3at | Surge protection at the entry point |
| PTZ | Cat6 or Cat6A | 100 m | 802.3at or 802.3bt | Motors and heaters need extra power |
| Multi-sensor | Cat6A | 100 m | 802.3at or 802.3bt | More bandwidth from several sensors |
| Pole or long-distance unit | Single-mode or multimode fiber | Up to several km | Local power or PoE at the pole | Media converter at each end |
| Legacy analog unit | Existing RG59 coax | Varies | Separate power | Replace with Cat6 or bridge with Ethernet-over-coax |
How we pull and protect each run
Every device gets its own home run back to the IDF, kept under the 100-meter limit and labeled with its ID at both ends. Indoors we use plenum-rated Cat6 in air-return ceilings. Outdoors we use UV-resistant or direct-burial Cat6 in conduit, mount a weatherproof back box behind each unit, leave a drip loop so water can’t reach the connection, and add a surge protector where the run enters the building. We use solid copper only, never copper-clad aluminum, which overheats under PoE load.
Video Surveillance Projects Across the City
These video surveillance projects show the kinds of buildings we work in every week.
Union Square stores
Ceiling runs to domes over registers, entrances and stockrooms, pulled overnight so stores open on time.
Bayview yards and docks
Outdoor runs in conduit to wall and pole mounts, with fiber to the far end of the yard where copper can’t reach.
SoMa parking garages
Runs along concrete ceilings to devices at every level, entry gate and stairwell, with surge protection on exposed runs.
Mission Bay labs
Coverage on every badge-entry door and corridor, run in plenum-rated Cat6 to the security IDF.
How We Plan and Pull Each Run
Plan device locations
We mark every unit on your floor plan with your integrator and confirm the IDF that will serve each one.
Check power and pathways
We total the PoE budget, check ceilings, walls and conduit routes, and plan fiber for any runs over 100 meters.
Pull and terminate
Each run is pulled, protected outdoors, terminated at both ends and labeled with its device ID.
Certify every link
Each run is tested to Cat6 or Cat6A limits, and any failing link is fixed and retested.
Hand off for mounting
You get a device map and test reports, and our technicians or yours can mount and connect right away.
Related Security Systems Services
These runs are one part of a complete security project. See our main security services overview, or our testing and certification page for how we certify every link.
- Mounting and NVR setup: Mounting, aiming and connecting the units these runs feed.
- Badge readers and door hardware: Readers, locks and door contacts on the same project.
Surveillance Service Area
We work in every neighborhood of the city, plus these Peninsula, East Bay and Marin cities:
- Daly City, CA
- Tiburon, CA
- Alameda, CA
- Oakland, CA
- South San Francisco, CA
- San Bruno, CA
- Albany, CA
- Berkeley, CA
- Piedmont, CA
- Mill Valley, CA
See every location on our service area page.
Request a Quote
Send your layout, a floor plan or the number of devices you’re adding, and we’ll schedule a walkthrough and return an itemized quote, usually within two business days.
San Francisco Telecom TechsOne Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]
Get every device connected, certified and ready to record.
Request a quote