Fiber Optic Splicing in San Francisco CA – #1 C7 Licensed Contractor

Fiber Optic Splicing in San Francisco CA

We fusion-splice single-mode and multimode fiber for pigtails, building entrances, mid-span joints and emergency repairs, then verify every splice with a bidirectional OTDR trace.

Need fiber optic splicing in San Francisco CA? Our C-7 licensed technicians use core-alignment fusion splicers that routinely hold splice loss under 0.05 dB, protect each joint in a heat-shrink sleeve, and organize every strand in labeled trays. From a single 12-strand pigtail job to a 288-fiber campus backbone, you get clean, low-loss splices and the test results to prove it.

Have a fiber cut, a new backbone to splice or a building entrance to transition? Call (628) 215-7235.

Request a quote

Fusion vs Mechanical Splicing

There are two ways to permanently join fiber. For backbone and campus links that need to last, fusion splicing is the standard, and it’s what we use on nearly every job.

Fusion splicing

An electric arc melts the two fiber ends together after the splicer aligns their cores, creating a continuous strand of glass. Loss is typically 0.02 to 0.05 dB with almost no reflection, and the joint stays stable for the life of the cable.

Mechanical splicing

The fiber ends are held together in an alignment sleeve with index-matching gel. It’s quicker to set up for a one-off repair, but loss runs higher, typically 0.1 to 0.5 dB, and the joint can drift over time. We use it only for temporary restoration.

Fiber splice methods compared by loss, reflectance and use
MethodTypical lossTIA-568.3-D maximumReflectanceBest for
Single-fiber fusion0.02–0.05 dB0.3 dB per spliceNegligiblePigtails, backbones, building entrances
Ribbon (mass) fusionAbout 0.05 dB average across 12 fibers0.3 dB per spliceNegligibleHigh-count backbones and campus cable
Mechanical0.1–0.5 dB0.3 dB per spliceMeasurable, varies with gelTemporary emergency restoration

Splicing Services We Provide

Whether the fiber is new or decades old, indoor or underground, we bring the splicer, the closures and the test gear to finish the job in one visit.

  • Pigtail splicing to the patch panel

    Factory-polished LC or SC pigtails fused to each strand inside a rack enclosure, giving lower loss and better reflectance than field-polished connectors.

    • LC / SC Pigtails
    • Rack Enclosures
    • Factory Polish
    • Low Reflectance
  • Building entrance splicing

    Outside plant cable transitioned to riser- or plenum-rated indoor fiber within 50 feet of where it enters the building, as the electrical code requires.

    • OSP to Indoor
    • 50 ft Rule
    • Entrance Closures
    • Armored Cable
  • Mid-span and through splicing

    Joining cable runs that exceed reel length or branching strands off a backbone, with splices organized in labeled trays inside a sealed closure.

    • Mid-Span Splices
    • Branching
    • Splice Trays
    • Sealed Closures
  • Ribbon (mass fusion) splicing

    Twelve fibers fused in a single pass for high-count ribbon cable, cutting splice time on large backbones and campus links.

    • 12-Fiber Ribbon
    • Mass Fusion
    • High Strand Counts
    • Faster Turnaround
  • Emergency restoration

    Cut or damaged fiber located with an OTDR, then repaired with new splices or a cable section so your network comes back up fast.

    • Fault Location
    • Cut Repair
    • Same-Day Response
    • Re-Certification
  • Splice enclosures and trays

    Rack-mount, wall-mount and outdoor closures sized for your strand count, with every splice protected and every tray labeled.

    • Rack-Mount
    • Wall-Mount
    • Outdoor Closures
    • Labeled Trays
Core-alignment fusion splicer joining two single-mode optical fibers
Core-alignment fusion splicer joining two OS2 single-mode fibers: cleave angle under 0.5 degrees on both ends and an estimated splice loss of 0.02 dB, well under the 0.3 dB TIA-568.3-D limit.

Splicing Projects Across San Francisco

Financial District building entrances

Transitioning carrier and campus outside plant cable to riser-rated fiber in basement entrance rooms of Market Street high-rises.

Mission Bay campus backbones

Ribbon splicing high-count single-mode cable between lab buildings, with sealed closures in underground vaults.

Embarcadero emergency repairs

Locating and restoring fiber damaged during construction along the waterfront, with re-certification once service is back.

SoMa server room pigtails

Pigtail splicing in high-density rack enclosures so every backbone strand lands on a factory-polished LC connector.

How We Fusion-Splice Each Strand

  1. Prepare and strip

    The cable jacket, strength members and buffer are removed, and the bare fiber is cleaned with lint-free wipes and alcohol.

  2. Cleave

    A precision cleaver cuts each fiber end flat, with a cleave angle under one degree for a low-loss joint.

  3. Align and fuse

    The splicer aligns the two cores on screen, fuses them with an electric arc and reports an estimated splice loss.

  4. Protect and organize

    Each splice is covered with a heat-shrink sleeve and seated in a labeled tray inside the enclosure or closure.

  5. Verify with OTDR

    Every strand is traced from both directions and the readings averaged, which gives a true splice loss and catches any bad joint.

Fiber splice tray with color-coded fibers and heat-shrink protected fusion splices
A 12-fiber splice tray with TIA-598 color-coded fibers, each joint protected by a 40 mm heat-shrink sleeve. Bidirectional OTDR averaging measured every splice between 0.01 and 0.04 dB.

Splicing is one stage of a complete fiber link. See our main fiber optic cabling page for the full overview.

Splicing Service Area in San Francisco and Nearby Cities

We splice fiber in every neighborhood of the city, plus these Peninsula, East Bay and Marin cities:

See every location on our service area page.

Request a Fiber Splicing Quote

Tell us the fiber type, strand count and where the splices need to go, or describe the outage, and we’ll respond with an itemized quote, usually within two business days. For a cut fiber, call and we’ll schedule a technician as quickly as we can.

San Francisco Telecom Techs
One Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]

Get low-loss splices that are protected, labeled and OTDR-verified.

Request a quote

Send us your project details