Structured Cabling Installation in San Francisco CA – #1 C7 Licensed Contractor

Structured Cabling Installation in San Francisco CA

We install complete structured cabling systems for commercial spaces: Cat6 and Cat6A horizontal runs to every outlet, an optical backbone between telecom rooms, terminations on patch panels, and labeling and certification testing on every link.

Looking for structured cabling installation in San Francisco CA? Our C-7 licensed low voltage technicians plan the pathways, pull and dress each run, terminate it and hand over test reports and as-built drawings, so your network infrastructure is ready the day your team moves in. We provide cabling services across San Francisco and the Bay Area, from single suites to full buildings.

Have a floor plan or drop count? Get an itemized installation quote. Call (628) 215-7235.

Request a quote

What’s Included: Cabling Design to Final Testing

Every installation follows the same sequence. We start by setting up pathways: J-hooks spaced no more than 5 feet apart, ladder rack in the telecom rooms, and sleeves through rated walls with firestopping. Each ethernet cable is then pulled from its outlet back to the IDF, keeping every permanent link under 90 meters and maintaining bend radius and separation from power.

At the rack, we terminate copper on angled or flat patch panels and backbone strands in LC enclosures, mount horizontal and vertical cable managers, and bond everything to the telecom grounding busbar. At the desk, we install faceplates, floor boxes and ceiling drops for access points and cameras. Finally, every port is labeled, tested and recorded on the as-built drawings. The same plant carries data cabling for workstations, voice lines and the wiring for access points, cameras and card readers.

  • Site survey, drop plan and pathway design
  • J-hook, cable tray and ladder rack installation
  • Cat6 or Cat6A horizontal cable pulls
  • OM4 or OS2 fiber optic backbone between floors
  • Patch panel, jack and LC terminations
  • Rack mounting and cable management
  • Firestopping at every penetration
  • TIA-606 labeling of every port and panel
  • Certification testing on every link
  • As-built drawings and port map
Plenum-rated Cat6A cable bundles supported on J-hooks above an office ceiling
Plenum-rated (CMP) Cat6A bundles supported on J-hooks every 4 feet, under the 5-foot maximum spacing in TIA-569, with no more than 50 cables per hook to avoid crushing the bottom of the bundle.

Installation Standards & Specifications

Good cabling design starts with clear specifications. These are the ones we build to on a typical commercial network installation. If your landlord or IT department has its own cabling standard, we follow that instead.

Structured cabling installation specifications and governing standards
ComponentSpecificationLimit or toleranceStandard
Horizontal cableCat6 or Cat6A, plenum-rated (CMP) in air-handling ceilings90 m permanent link, 100 m channelTIA-568.2-D
Optical backboneOM4 multimode inside the building, OS2 single-mode between buildings≤0.3 dB per splice, ≤0.75 dB per connector pairTIA-568.3-D
Bend radiusCopper during and after installation4× cable diameter (installed)TIA-568.0-E
Pathway supportJ-hooks or cable tray≤5 ft (1.5 m) between supportsTIA-569-E
Separation from powerUnshielded copper near fluorescent lights and power circuits5 in from lighting fixtures; follow NEC 800.133TIA-569-E, NEC
LabelingFaceplates, patch panels, cables at both endsUnique ID per port: floor-room-rack-portTIA-606-C
GroundingRacks and ladder rack bonded to telecom grounding busbar6 AWG minimum bonding conductorTIA-607-D

Cat6 or Cat6A: which ethernet cable should you install?

Cat6

Supports 1 Gbps to 100 m and 10 Gbps to about 55 m. A sound, lower-cost choice for workstations, printers and VoIP phones in smaller spaces where runs stay short.

Cat6A

Supports 10 Gbps to the full 100 m and handles the heat of high-wattage PoE better. The right choice for Wi-Fi 6E and Wi-Fi 7 access points, PoE lighting and any space you plan to occupy for more than a few years.

Buildings and Spaces We Wire

  • Open-plan offices
  • High-rise office floors
  • Lab and life science suites
  • Warehouses and distribution centers
  • Medical offices and clinics
  • Classrooms and campus buildings
  • Retail stores and back offices
  • Historic and masonry buildings

Financial District office floors

Floor-by-floor Cat6A installs in Market and Montgomery Street towers, pulled after hours to meet building rules and tied into the base-building riser backbone.

Presidio historic offices

Low-profile surface raceway and careful routing through converted barracks and brick buildings, where walls and ceilings can’t be opened freely.

Mission Bay labs

Plenum-rated runs for lab benches and instrument networks, installed around ductwork, gas lines and cleanroom ceilings in life science suites.

Dogpatch and Potrero Hill creative spaces

Exposed-ceiling offices and studios where cable tray stays visible, so neat bundling and straight runs matter as much as performance.

Our Installation Process

  1. Walk the site

    We review floor plans, measure pathways, locate the telecom rooms and confirm every outlet is within 90 m of its IDF.

  2. Plan and price

    You receive a drop schedule, rack elevations and a line-item quote, with cable type and labeling scheme agreed before work starts.

  3. Set up pathways

    J-hooks, tray, ladder rack and sleeves go in first, with firestopping at each rated wall.

  4. Pull and dress network cable

    Cable is pulled in bundles, routed to the correct IDF and dressed neatly into the rack.

  5. Terminate and mount

    Copper is punched down to panels and jacks, backbone strands are spliced or terminated, and faceplates are mounted.

  6. Test, label and hand off

    Every link is certified and labeled, and you get the test reports, port map and as-built drawings.

Testing, Labeling & Documentation

Each copper network cable is certified with a field tester against TIA-568.2-D permanent link limits, covering wire map, length, insertion loss, NEXT and return loss. Backbone strands are tested for end-to-end loss, with OTDR traces on every riser run. Any link that fails is reterminated and retested before we call the job complete.

The closeout package includes PDF test reports exported straight from the tester, a port map matching every label, and as-built drawings showing each outlet and cable route. Certified installations also qualify for manufacturer system warranties.

48-port Cat6A patch panel for a structured cabling rack
A 48-port Cat6A patch panel labeled to TIA-606, with each port ID (for example 03-IDF2-R1-P24) matching its faceplate, the port map and the certification report.

Structured Cabling Installation FAQ

How long does an installation take?

It depends on drop count, ceiling access and building rules. A small office can often be cabled in a few days, while a full high-rise floor usually takes one to three weeks. We give you a schedule with the quote.

Can you work after hours?

Yes. Many downtown San Francisco buildings only allow noisy work or freight elevator use at night or on weekends, and we schedule our cabling services around that.

Will you remove the old cable?

Yes. The electrical code requires removing accessible abandoned cable, and we include it in the scope when the space has old cabling left in the ceiling.

Do you install the backbone too?

Yes. We pull, splice and test the fiber cables between your MDF and IDFs, so one crew is responsible for the whole system.

Installation Service Area

We install structured cabling in every neighborhood of the city, plus these Peninsula, East Bay and Marin cities:

See every location on our service area page.

Request an Installation Quote

For structured cabling, San Francisco businesses can send a floor plan, drop count or a description of the space, and we’ll schedule a site walk and return an itemized quote, usually within two business days.

San Francisco Telecom Techs
One Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]

Get your cabling installed, labeled and certified on schedule.

Request a quote

Send us your project details