Fiber Optic Cabling in San Francisco CA – #1 C7 Licensed Contractor

Fiber Optic Cabling in San Francisco CA

We install, splice, terminate and certify single-mode and multimode fiber for commercial networks, from riser backbones between telecom rooms to campus links between buildings.

Looking for fiber optic cabling in San Francisco CA? Our C-7 licensed technicians pull fiber through risers, conduit and ceilings, fusion-splice pigtails and building entrances, mount labeled enclosures in your racks, and hand you Tier 1 and Tier 2 test results for every strand. One crew handles the whole link, so there’s no gap between the installer, the splicer and the tester.

Need a new backbone, a campus link or a fiber repair? Get a site walk and itemized quote. Call (628) 215-7235.

Request a quote

Fiber Optic Cabling Services

Every fiber link goes through the same four stages. We offer each one on its own, or as a complete install-to-certification package.

Fiber vs Ethernet Cable: Where Each Fits

Copper handles the last 90 meters to each desk, access point and camera. Fiber carries everything else: the backbone between your main distribution frame and each floor’s IDF, links between buildings on a campus, and high-speed connections between racks in a server room. It carries 10, 40 and 100 Gbps over distances copper can’t reach, and because it’s made of glass, it’s immune to the electrical interference found near elevators, motors and lab equipment.

Most of our projects pair OM4 multimode for backbones inside a building with OS2 single-mode for longer runs and links to other buildings. We install it in innerduct or armored jacket where it needs protection, keep bends wider than the cable’s minimum radius, and leave spare strands in every run so the next upgrade doesn’t mean pulling new cable.

Comparison of fiber optic cable types we install
Fiber typeCore / jacket colorWavelength10 Gbps reach100 Gbps reachTypical use
OM3 multimode50 µm, aqua850 nm300 m100 m (SR4)Existing backbones, short in-building links
OM4 multimode50 µm, aqua or violet850 nm400 m150 m (SR4)Riser backbones, MDF-to-IDF, server rooms
OM5 multimode50 µm, lime green850–953 nm (SWDM)400 m150 m (SR4)Data rooms planning for wavelength multiplexing
OS2 single-mode9 µm, yellow1310 / 1550 nm10 km (LR)10 km (LR4)Campus links, long risers, carrier circuits
Armored / outside plantSingle-mode or multimode, black outer jacketPer fiber typePer fiber typePer fiber typeUnderground conduit, building-to-building
Rack-mount fiber enclosure with OM4 and OS2 LC duplex connectors
A 1U rack enclosure terminating a 24-strand OM4 riser backbone (aqua) and a 12-strand OS2 campus link (yellow) on LC duplex adapters, each strand labeled to TIA-606.

Facilities we wire with fiber and network cable

  • Multi-floor office towers
  • Corporate campuses
  • Life science and lab buildings
  • Server rooms and data closets
  • Hospitals and medical offices
  • Schools and universities
  • Warehouses and distribution centers
  • Hotels and hospitality

Projects From Your Local Fiber Cabling Installer

Financial District riser backbones

OM4 and OS2 backbones run up shared risers in Market and California Street towers, connecting a tenant’s MDF to IDFs on every leased floor.

Mission Bay campus links

Armored single-mode fiber through underground conduit between lab buildings, spliced at each entrance and certified end to end.

Embarcadero pier offices

Fiber routed through the long, open spans of converted waterfront piers, where copper runs would exceed the 90 m limit.

SoMa server rooms

MTP/MPO trunks and high-density LC panels linking racks for 40 and 100 Gbps switch uplinks in tech company data rooms.

How We Install Fiber Optic Cable

  1. Survey and link design

    We map the route, measure distances, choose fiber type and strand count, and calculate a loss budget for each link.

  2. Pathway and cable installation

    Innerduct, conduit and ladder rack go in first, then fiber is pulled under its tension rating with bend radius protected at every turn.

  3. Splicing and termination

    Pigtails are fusion-spliced or connectors terminated, then strands are dressed into labeled enclosures and adapter panels.

  4. Testing and certification

    Every strand gets Tier 1 loss testing and a Tier 2 OTDR trace, checked against the loss budget.

  5. Documentation

    You receive strand maps, test reports and as-built drawings for your IT team and building management.

OTDR trace of a single-mode fiber link showing splice and connector loss events
OTDR trace of a 180 m OS2 link: two fusion splices at 0.03 and 0.04 dB, two LC connector pairs, and 0.9 dB total loss against a 2.6 dB budget.

Fiber Optic Cabling Service Area

We install fiber in every neighborhood of the city, plus these Peninsula, East Bay and Marin cities:

See every location on our service area page.

Request a Fiber Optic Cabling Quote

Send a floor plan, the locations you need to connect or a description of the problem, and we’ll schedule a site walk and return an itemized quote, usually within two business days.

San Francisco Telecom Techs
One Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]

Get fiber that’s installed, spliced and certified on schedule.

Request a quote

Send us your project details