Wireless Network Cabling in San Francisco CA – #1 C7 Licensed Contractor

Wireless Network Cabling in San Francisco CA

We run the cable behind your Wi-Fi: certified Cat6A drops from the IDF to every AP, sized for multi-gig speeds and the PoE power that Wi-Fi 6E and Wi-Fi 7 hardware needs.

Need wireless network cabling in San Francisco CA? Every AP is only as fast as the cable feeding it. As a C-7 licensed low voltage contractor, our crews plan drop locations with your Wi-Fi design, pull Cat6A through ceilings and conduit, terminate each run at the AP, and certify every link so your new hardware reaches full speed on day one.

Adding APs or upgrading to Wi-Fi 7? Get an itemized cabling quote. Call (628) 215-7235.

Request a quote

Network Wiring, Not Just APs, Fixes Dead Zones

Every Wi-Fi AP is wired. Each one needs a network cable that carries data back to the switch and the PoE power that runs it. New APs push both harder than older ones: a Wi-Fi 7 AP can use a 5 or 10 Gbps uplink and draw 40 watts or more. Old Cat5e, long runs and crowded bundles can cap the uplink at 1 Gbps or leave the AP short on power, which users notice as slow Wi-Fi and dead zones.

That’s why we run Cat6A to every new AP location. It carries 10 Gbps over the full 100-meter channel and stays cooler in large PoE bundles, so the same network wiring will support the next two generations of hardware.

What Our AP Cabling Includes

  • Cat6A AP drops

    A dedicated Cat6A run from the IDF to every AP location, sized for multi-gig uplinks today and the next upgrade after that.

    • Cat6A
    • Ceiling Drops
    • Multi-Gig
    • Plenum Rated
  • Dual drops for Wi-Fi 7

    Two runs to each high-capacity AP for 10 Gbps link aggregation or a redundant uplink, so one bad port never takes an area offline.

    • Two Drops per AP
    • Link Aggregation
    • Redundancy
    • Wi-Fi 7 Ready
  • PoE budget and switch planning

    We total the power draw of every AP, camera and phone so your PoE switches and UPS are sized correctly, with headroom for growth.

    • 802.3at / 802.3bt
    • PoE Budget
    • Switch Sizing
    • UPS Load
  • Ceiling terminations and service loops

    Runs end in a surface-mount jack or an MPTL plug at the ceiling, with a service loop that lets the AP move without a new pull.

    • Surface-Mount Jacks
    • MPTL
    • Service Loops
    • AP Brackets
  • Outdoor and warehouse runs

    Outdoor-rated cable in conduit for patios, courtyards and parking areas, and high-bay drops along warehouse racking.

    • Outdoor Rated
    • Conduit
    • High-Bay
    • Racking Aisles
  • Cat5e replacement for upgrades

    Old Cat5e can bottleneck new APs. We pull out the legacy cables, run Cat6A in their place and remove abandoned runs as code requires.

    • Cat5e Removal
    • Cat6A Upgrade
    • Cable Abatement
    • Minimal Downtime

Cabling Requirements by AP Type

Here’s what we plan for each kind of AP. Exact power depends on the model, so we confirm it against the manufacturer’s data sheet during design.

Cable, uplink and PoE requirements for each AP type
AP typeUplink speedCable we installDrops per APPoE standardTypical power at AP
Wi-Fi 61–2.5 GbpsCat6 or Cat6A1802.3at (PoE+)Up to 25.5 W
Wi-Fi 6E2.5–5 GbpsCat6A1802.3at or 802.3bt25–40 W
Wi-Fi 75–10 GbpsCat6A1–2802.3bt (PoE++)40–51 W
Outdoor AP1–5 GbpsOutdoor-rated Cat6A in conduit1802.3at or 802.3bt25–51 W
Warehouse high-bay AP1–5 GbpsCat6A, often in conduit1802.3at or 802.3bt25–40 W

How we install each network cable

Every run stays under the 90-meter permanent link limit, so we confirm which IDF serves each AP before pulling. Cable is plenum-rated wherever the ceiling carries return air, supported on J-hooks every five feet, and bundled loosely in small groups so PoE heat can escape, following TIA TSB-184-A. At the AP end we leave a coiled service loop of about 10 feet, then terminate to a surface-mount jack or a field-installed plug for a modular plug terminated link (MPTL), as TIA-568.2-D allows. In the IDF, each run lands on patch panels with proper cable management, and both ends are labeled with the AP’s ID.

Cat6A cable drops terminated at a ceiling-mounted Wi-Fi access point
Dual Cat6A drops to a Wi-Fi 7 AP: each run certified at under 90 m, terminated in a ceiling surface-mount box with a 10 ft service loop, delivering 10 Gbps link aggregation and 802.3bt power.

AP Cabling Projects Across the City

SoMa open ceilings

Cat6A drops run neatly along exposed cable tray to dozens of APs in converted warehouse offices, where every cable is visible.

Financial District Wi-Fi 7 upgrades

Replacing Cat5e above occupied floors in older office buildings with dual Cat6A drops, scheduled after hours so tenants keep working.

Union Square hotel corridors

One drop per corridor AP across every guest floor, run in tight ceiling spaces with plenum-rated cable and minimal disruption to guests.

Bayview warehouse aisles

High-bay AP drops in conduit along racking aisles, protected from forklifts and kept within reach of the nearest IDF.

How We Run AP Cabling

  1. Site survey and drop plan

    We start with a site survey, mark every AP location on the floor plan and confirm the IDF and switch port that will serve it.

  2. Check power and pathways

    We total the PoE budget, check ceiling clearance and conduit, and flag any runs that need a closer IDF.

  3. Pull and terminate

    Cat6A is pulled, supported, terminated at both ends and labeled with the AP’s ID.

  4. Certify every link

    Each run is tested to Cat6A permanent link limits, and any failing link is fixed and retested.

  5. Hand off for AP install

    You get a drop map and test reports, and the AP installers, ours or yours, can mount and connect right away.

Testing & Certification

Every AP drop is certified to TIA-568.2-D Category 6A limits across the full 500 MHz range, measuring wire map, length, insertion loss, NEXT and return loss on all four pairs. Results are exported as PDF reports labeled by AP ID. See how we test on our testing and certification page.

Cabling is one part of a complete network installation. See our Wi-Fi overview page, or our Cat6A page for more on the cable itself. We also offer cabling services for phones, cameras and every other device in the building.

AP Cabling Service Area

We provide cabling services in every neighborhood of the city, plus these Peninsula, East Bay and Marin cities:

See every location on our service area page.

Request an AP Cabling Quote

Send your AP layout, a floor plan or the number of APs you’re adding, and we’ll schedule a walkthrough and return an itemized quote, usually within two business days.

San Francisco Telecom Techs
One Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]

Get every AP cabled, certified and ready for full speed.

Request a quote

Send us your project details