VoIP Cabling in San Francisco CA – #1 C7 Licensed Contractor

VoIP Cabling in San Francisco CA

We wire offices for VoIP phone systems: Cat6 drops to every desk and conference room, PoE power from the switch, analog lines for the devices that still need them, and removal of the old phone wiring you no longer use.

Need VoIP cabling in San Francisco CA? Whether you’re retiring an old PBX or moving into a new space, our C-7 licensed technicians run and certify the Cat6 your phones need, size the PoE switches and UPS so phones stay up, and coordinate with your phone provider so every handset registers on cutover day.

Switching to VoIP or adding phones? Get a walkthrough and itemized quote. Call (628) 215-7235.

Request a quote

Why VoIP Needs New Cabling

Traditional office phones ran on Cat3 or 25-pair cable punched down to 66 blocks in a phone closet. That wiring carries a dial tone, but it can’t carry Ethernet. VoIP phones are network devices: each one needs a Cat5e or better drop to a switch port, and most draw their power over that same cable through Power over Ethernet (PoE), so there’s no power brick at the desk.

We install Cat6 for every new phone drop. It runs gigabit to the desk, handles PoE without trouble, and gives you the option to share one drop between the phone and computer or later convert a phone drop into a data drop as the office changes.

Hosted VoIP or premise-based VoIP: the cabling is the same

Whether you use a cloud phone service or a phone server of your own, every handset still needs a Cat6 drop and PoE. The difference is in the telecom room: an on-site system adds a phone server and sometimes analog gateways that need rack space, power and a network connection, which we plan into your MDF or IDF.

What Our VoIP Cabling Includes

  • Cat6 phone drops

    A Cat6 run to every desk, reception counter and conference table, terminated, labeled and patched to a PoE switch port.

    • Cat6
    • Desk Drops
    • PoE Ready
    • Labeled Ports
  • Shared or dedicated desk drops

    One drop shared by the phone and PC through the phone’s switch port, or two drops per desk so the computer gets its own full-speed link.

    • Phone Pass-Through
    • Dual Drops
    • Gigabit to PC
    • Hot Desks
  • PoE switch and UPS sizing

    We add up every phone’s power draw so your PoE switches and UPS can run the whole phone system, including through a short outage.

    • PoE Budget
    • Switch Sizing
    • UPS Runtime
    • 911 Readiness
  • Conference, reception and video phones

    Drops for conference phones, receptionist consoles with sidecars and video phones, placed where the furniture plan puts them.

    • Conference Phones
    • Reception Consoles
    • Video Phones
    • Floor Boxes
  • Analog lines for fax, alarms and elevators

    Fax machines, alarm panels, elevator phones and fire panels still need analog lines. We wire analog telephone adapters (ATAs) or keep those circuits on dedicated pairs.

    • Fax Lines
    • Elevator Phones
    • Alarm Panels
    • ATAs
  • Legacy phone wiring removal

    Old Cat3, 25-pair cable and 66 punch blocks are removed or retired as code requires, freeing up ceiling space and closet walls.

    • Cat3 Removal
    • 66 Blocks
    • 25-Pair Cable
    • Closet Cleanup

Power and Cabling by Phone Type

VoIP phones draw far less power than access points or cameras, but the total adds up across an office. These are the figures we plan PoE budgets around, confirmed against each model’s data sheet.

Cabling and PoE power requirements for common VoIP devices
DeviceCablingPoE classTypical power drawNotes
Basic desk phoneOne Cat6 dropClass 1–2 (802.3af)3–6.5 WOften shares the drop with the PC
Executive phone with sidecarOne Cat6 dropClass 2–3 (802.3af)6.5–13 WSidecars add power draw
Video phoneOne Cat6 dropClass 3–4 (802.3af/at)13–25.5 WMay need PoE+ switch ports
Conference phoneCat6 drop at table or floor boxClass 2–3 (802.3af)6.5–13 WPlan placement with furniture
DECT base stationOne Cat6 drop, ceiling or wallClass 1–2 (802.3af)3–6.5 WFor cordless handsets
Analog adapter (ATA)Cat6 to the ATA, analog pair to the deviceLocal power or PoEUnder 6.5 WFax, alarm, elevator lines

One drop or two per desk?

Most VoIP phones have a built-in switch port, so a single drop can feed both the phone and the computer. That saves cable, but the computer’s speed is limited to the phone’s port, and a phone reboot drops the PC too. For most offices we recommend two drops per workstation: one for the phone and one for the computer. The cost difference is small during a new install and much larger to add later.

Dual-port Cat6 wall plate for a VoIP desk phone and computer at an office workstation
Dual-port Cat6 wall plate labeled to TIA-606: port A feeds an 802.3af PoE desk phone, port B gives the computer its own gigabit link, both certified and patched to the floor’s IDF.

VoIP Cabling Projects Across San Francisco

Financial District PBX retirements

Replacing decades-old 25-pair phone wiring in Montgomery Street offices with Cat6, then removing the old 66 blocks from the phone closet.

SoMa sales floors

Dense rows of desks with two drops each, PoE switches sized for every headset phone, and UPS runtime planned for the whole floor.

Inner Sunset medical offices

Reception consoles, exam room phones and dedicated fax lines through analog adapters for practices near UCSF Parnassus.

Union Square retail and hotels

Front desk and back-office phones, cordless DECT coverage for floor staff, and analog lines for elevator emergency phones.

How We Install VoIP Cabling

  1. Walkthrough and phone count

    We mark every phone location, confirm one or two drops per desk, and find the analog devices that still need lines.

  2. PoE and switch planning

    We total phone power, check switch ports and UPS capacity, and confirm cutover timing with your phone provider.

  3. Cable and terminate

    Cat6 is pulled, terminated at both ends, labeled and patched to the switch ports your IT team designates for voice.

  4. Certify and test

    Every drop is certified, and we confirm phones power up and get dial tone at each location.

  5. Clean up old wiring

    Legacy phone cable and punch blocks are removed or retired, and you get a port map and test reports.

Phones are one part of how your office communicates. See our main voice / communications page for the full overview, or our Cat6 cabling page for more on the cable itself.

VoIP Cabling Service Area

We wire VoIP phone systems in every neighborhood of the city, plus these Peninsula, East Bay and Marin cities:

See every location on our service area page.

Request a VoIP Cabling Quote

Send a floor plan, your phone count and any fax, alarm or elevator lines you need to keep, and we’ll schedule a walkthrough and return an itemized quote, usually within two business days.

San Francisco Telecom Techs
One Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]

Get every phone wired, powered and ready for cutover day.

Request a quote

Send us your project details