Security Camera Cabling in San Francisco CA – #1 C7 Licensed Contractor

Security Camera Cabling in San Francisco CA

We run the lines behind your surveillance: Cat6 PoE runs from the telecom room to every device, outdoor runs in conduit, and fiber for parking lots and yards beyond copper’s reach.

Need security camera cabling in San Francisco CA? Our C-7 licensed technicians plan each mounting location with you, pull and terminate a dedicated run to every device, protect outdoor runs from weather and surges, and certify every link, so your commercial security stays powered, online and recording clear footage day and night.

Adding new devices or replacing old coax? Get an itemized quote. Call (628) 215-7235.

Request a quote

Why the Run Behind Each Device Matters

An IP dome or bullet depends on one line for everything: footage back to the recorder and PoE power for the unit, its infrared lights and, on outdoor models, its heater. Long runs, damaged jackets, copper-clad wire and unprotected outdoor connections are the usual reasons devices drop offline, reboot at night when the IR turns on in low light, or record grainy footage. Doing the runs right prevents all of these before the first unit goes up, whether you’re replacing old CCTV cabling or adding security cameras to existing security systems.

What’s Included in Every Surveillance System Run

  • PoE drops

    A dedicated Cat6 home run from the IDF to every device, carrying footage and PoE power on one line, labeled by device ID.

    • Cat6
    • Dedicated Runs
    • PoE Power
    • ID Labels
  • Outdoor and perimeter runs

    Outdoor-rated Cat6 in conduit to wall, roof and pole mounts, with weatherproof junction boxes, drip loops and surge protection where runs enter the building.

    • Outdoor Rated
    • Conduit
    • Junction Boxes
    • Surge Protection
  • Long runs past 100 meters

    Parking lots, yards and gates beyond copper’s reach get fiber with media converters, or PoE extenders for shorter gaps.

    • Fiber Links
    • Media Converters
    • PoE Extenders
    • Pole Mounts
  • PTZ and high-power units

    Cat6A and 802.3bt-ready runs for PTZ, multi-sensor and heated outdoor units that draw more power than a standard dome.

    • Cat6A
    • 802.3bt
    • PTZ
    • Multi-Sensor
  • Analog to IP upgrades

    Replacing old coax with Cat6 for IP devices, or using Ethernet-over-coax adapters as a stopgap where new runs aren’t possible yet.

    • Coax Removal
    • Cat6 Upgrade
    • Ethernet over Coax
    • Phased Upgrades
  • NVR and head-end work

    Patch panels, PoE switches, UPS power and tidy cable management in the telecom room, sized so every device has power and a clean path to the recorder.

    • PoE Switches
    • Patch Panels
    • UPS
    • NVR Connections

Surveillance Cameras and the Runs They Need

Here’s what we plan for each type of unit. Exact power depends on the model, so we confirm it against the manufacturer’s data sheet during design.

Run length, media and PoE requirements by device type
Device typeWhat we installMax runPoE standardNotes
Indoor dome or turretCat6, plenum where required100 m802.3afMost common in offices and stores
Outdoor bullet or dome with IROutdoor-rated Cat6 in conduit100 m802.3af or 802.3atSurge protection at the entry point
PTZCat6 or Cat6A100 m802.3at or 802.3btMotors and heaters need extra power
Multi-sensorCat6A100 m802.3at or 802.3btMore bandwidth from several sensors
Pole or long-distance unitSingle-mode or multimode fiberUp to several kmLocal power or PoE at the poleMedia converter at each end
Legacy analog unitExisting RG59 coaxVariesSeparate powerReplace with Cat6 or bridge with Ethernet-over-coax

How we pull and protect each run

Every device gets its own home run back to the IDF, kept under the 100-meter limit and labeled with its ID at both ends. Indoors we use plenum-rated Cat6 in air-return ceilings. Outdoors we use UV-resistant or direct-burial Cat6 in conduit, mount a weatherproof back box behind each unit, leave a drip loop so water can’t reach the connection, and add a surge protector where the run enters the building. We use solid copper only, never copper-clad aluminum, which overheats under PoE load.

Outdoor security camera on a building wall with a weatherproof junction box and conduit
Outdoor run done right: outdoor-rated Cat6 in conduit to a weatherproof junction box with a drip loop, certified at 68 m and protected by a surge suppressor at the entry point.

Video Surveillance Projects Across the City

These video surveillance projects show the kinds of buildings we work in every week.

Union Square stores

Ceiling runs to domes over registers, entrances and stockrooms, pulled overnight so stores open on time.

Bayview yards and docks

Outdoor runs in conduit to wall and pole mounts, with fiber to the far end of the yard where copper can’t reach.

SoMa parking garages

Runs along concrete ceilings to devices at every level, entry gate and stairwell, with surge protection on exposed runs.

Mission Bay labs

Coverage on every badge-entry door and corridor, run in plenum-rated Cat6 to the security IDF.

How We Plan and Pull Each Run

  1. Plan device locations

    We mark every unit on your floor plan with your integrator and confirm the IDF that will serve each one.

  2. Check power and pathways

    We total the PoE budget, check ceilings, walls and conduit routes, and plan fiber for any runs over 100 meters.

  3. Pull and terminate

    Each run is pulled, protected outdoors, terminated at both ends and labeled with its device ID.

  4. Certify every link

    Each run is tested to Cat6 or Cat6A limits, and any failing link is fixed and retested.

  5. Hand off for mounting

    You get a device map and test reports, and our technicians or yours can mount and connect right away.

These runs are one part of a complete security project. See our main security services overview, or our testing and certification page for how we certify every link.

Surveillance Service Area

We work in every neighborhood of the city, plus these Peninsula, East Bay and Marin cities:

See every location on our service area page.

Request a Quote

Send your layout, a floor plan or the number of devices you’re adding, and we’ll schedule a walkthrough and return an itemized quote, usually within two business days.

San Francisco Telecom Techs
One Beach St, San Francisco, CA 94133
Phone: (628) 215-7235
Email: [email protected]

Get every device connected, certified and ready to record.

Request a quote

Send us your project details